-40%
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more
YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more

YODER T.I.G. WELD TUBE MILL uncoiler, mill, saw, roll stand, sizing mill, more

$ 92400

Availability: 100 in stock
  • Condition: Used
  • All returns accepted: ReturnsNotAccepted
  • Brand: yoder

    Description

    REFERENCE NUMBER: 29029
    SPECIFICATIONS:
    Reference #: 29029
    Model Number: W-15/W-20
    Serial Number: Y-3045-385
    Hand of Operation: Left to Right
    Catalog Capacity: W-15 – 1-1/2″ Diameter x .083″ Max. Wall
    Carbon Steel – .375″ Min. Diameter
    Catalog Capacity: W-20 – 3″ Diameter x .120″ Max. Wall
    Carbon Steel – .500″ Min. Diameter
    Note: With special tooling, this tube mill will make 3-1/2″ diameter or larger.
    EQUIPMENT SUMMARY
    Single End Uncoiler:
    Manufactured by Cooper Weymouth-Peterson
    Model Number: 4R-18
    Serial Number: 19613
    Capacity: 8,000 Lbs.
    Coil Width: 15″ Maximum
    Electric Brake
    1 H.P. Feed Up Motor
    1 Set of Coil Keepers
    Forming Mill:
    Model W-20 (2 Sets of Rafted Stands; 1 Set is Mounted on the Mill Bases)
    Pass Arrangement:
    1 – Entry Guide Stand
    4 – Driven (Lower Shaft Only) Breakdown Stands; 2″Shafts
    3 – Driven Fin Stands; 2″ Shafts
    7 – Idle Sideroll Stands
    Note: All driven stands are driven by 40:1 cone drive gearbox through universal drive shaft with quick disconnect feature.
    Weld Section:
    1 – Olympia V.T. (Italy) Weld Unit with Cyclomatic Magnetic Arc Control
    1 – Torch 4-Roll (2 Sets Mounted in Tandem) Enclosed in an Atmospheric Weld Station
    Powered by Miller Syncrowave 350 A.C./D.C. Welder
    Weld Condition Monitor; Manufactured by Pruf Technik; Model LAB 2004
    2-Roll Ironing Stand:
    With Mandrel Bracket and Mandrel Mounted Upstream
    Stainless Steel Cooling Trough:
    Sizing Mill:
    Model W-20 (2 Sets of Rafted Stands; 1 Set is Mounted on the Mill Bases)
    Pass Arrangement:
    3 – Driven Sizing Stands; 2″Shafts
    3 – Idle Sideroll Stands
    1 – 4-Roll Straightening Turkshead
    Mill Drive:
    2 – Reliance Drives
    2 – Model D.C. Integrators Model 590 Plus
    2 – 7.5 H.P. D.C. Motors
    Complete with Operator’s Bench and Saw Operator’s Bench and Transformers.
    Cut-Off Saw:
    Abrasive Saw
    Entry & Exit Clamping (Hydraulic)
    4′ Travel by Hydraulic Cylinder
    Everet Saw Head Model 26; Serial Number 945-8; Mounted on Thompson Shafting
    30 H.P. A.C. Motor; 1750 RPM
    26″ Diameter Abrasive Blade
    Hydraulic Downfeed
    20′ Run-Out Table:
    Tooling: Some tooling is included, but not inventoried.
    Large amount of technical manuals and drawings.
    Note: Also included is a complete set of Model W-15 rafted stands with 1-1/2″ shafts and idle sideroll stands with the same pass arrangement described above that also connect to the cone drive gearboxes through universal drive shafts.